Bafang Error 26 indicates a load sensor fault, which occurs when the motor controller detects an impossible or conflicting reading from the internal torque-and-cadence sensing module. In systems equipped with dual-sensing mid-drives or torque-sensing bottom brackets, the load sensor calculates pedal effort by comparing physical spindle strain against pedal rotation speed. If the controller registers heavy torque without corresponding rotation pulses—or if cadence pulses arrive out of sequence—it logs Error 26 and disables motor assistance to prevent sudden surges.
Fast Fix
Turn off the display. Rotate the pedals backward five full turns by hand to dislodge any road grit trapped between the chainring spider and the motor housing. Inspect the sensor wiring connector near the bottom bracket, disconnect and firmly reseat it, then power on the bike while keeping your feet completely off the pedals.
Quick Status & Safety
- Severity: Moderate to High. Pedal assist is shut off by the controller, but manual pedaling and braking remain normal.
- Safe to ride: Yes, as an unassisted bicycle. If your e-bike has a standalone throttle, it may continue to function depending on your firmware profile.
- Likely cause: Cadence magnet ring displacement inside the load sensor, loose sensor wiring, bottom bracket axle play, or foreign debris binding the crank spider.
What This Means
Bafang mid-drive systems (like the M500, M510, M600, and M620 Ultra) use a composite load sensor that combines two distinct measuring circuits into one unit:
- The torque circuit: Measures the torsional strain (twisting force) applied to the bottom bracket axle.
- The cadence/load pulse circuit: Uses a multi-pole magnetic ring and dual Hall-effect switches to measure how fast and in what direction the crankarms are spinning.
To calculate how much electrical assist to deliver, the controller cross-checks both circuits. If you stand on the pedals while stopped at a red light, the torque sensor outputs a high-load voltage, but the cadence sensor reports zero rotational pulses. Under normal programming, this is permitted for a brief pause. However, if that high-load signal continues or fluctuates without rotation while the bike is commanded to move, the controller flags Error 26 because the load signal violates programmed operational logic.
Diagnostic Path
Use these riding conditions to isolate the cause:
- The error triggers the instant you turn on the bike:
- Suspect: Internal sensor Hall switch failure, a severed pulse wire in the harness, or a startup zero-load calibration failure.
- The error appears only when pedaling forward, but the bike powers on normally:
- Suspect: The cadence pulse ring inside the load sensor is slipping on the spindle, or debris is interfering with the magnetic pickup.
- The error occurs when pedaling backward or shifting gears under load:
- Suspect: A faulty directional Hall sensor inside the cartridge that cannot determine forward versus reverse crank rotation.
- The throttle drives the motor normally, but pedaling triggers Error 26:
- Suspect: The motor drive, battery, and controller phase circuits are intact; the fault is confined strictly to the bottom bracket load-sensing core.
Likely Causes
1. Internal Cadence Pulse Discrepancy
Inside the torque/load cartridge, a circular disc with alternating magnetic poles spins past two small Hall sensors. If this disc slips out of alignment or if one of the Hall sensors burns out, the controller receives the strain gauge load signal without the necessary timing pulses. For an overview of sensor differences, see Torque Sensor vs. Cadence Sensor Failure: Key Differences.
2. Mechanical Contamination in the Chainring Spider
Mid-drive motors have a freewheeling clutch mechanism and spider assembly around the axle. If mud, fine gravel, or road grit packs into the small gap between the motor shell and the chainring spider, it can bind the rotating assembly, preventing the load sensor from returning to its neutral resting state.
3. Loose Bottom Bracket Bearings or Spindle Play
Heavy trail riding or high mileage can wear out the internal cartridge bearings. When bearings develop play, the axle tilts under load. This tilt shifts the internal sensor components out of alignment, causing erratic load spikes.
4. Moisture Ingress or Damaged Wiring
Water seeping past the bottom bracket seals can short out the 5V logic supply feeding the internal Hall sensors. A pinched or damaged sensor harness will also cause pulse dropouts. For cleaning guidance, see How to Clean E-Bike Electrical Connectors Safely.
Commonly Confused Problems
- Bafang Error 17: Error 17 indicates a baseline zero-point torque calibration offset, typically triggered by resting a foot on the pedals at startup. See Bafang Error 17: Torque Sensor Signal Fault Fix.
- Bafang Error 25: Error 25 indicates that the torque sensor’s analog voltage output is outside electrical bounds (open circuit or short). Review Bafang Error 25: Torque Sensor Signal Error Fix.
- General Cadence Failure: If the motor will not engage when pedaling, but no code appears on the screen, check E-Bike Cadence Sensor Failure: Pedal Assist Not Engaging.
What To Do
Step 1: Perform a Zero-Load Power Cycle
- Place the e-bike on flat ground or a work stand.
- Ensure both pedals hang completely free without touching the ground or any objects.
- Turn the display off, wait 15 seconds, and turn it back on.
- Spin the cranks forward by hand for two full rotations. If the error stays cleared and the display registers cadence or assist, the issue was an uncalibrated zero-load reading.
Step 2: Clear Mechanical Obstructions
- Inspect the gap between the chainring, spider, and the motor housing.
- Use a brush or compressed air to remove built-up dirt, twigs, or dried mud.
- Rotate the cranks backward and listen for scraping or grinding noises. The crank should spin backward with smooth, light resistance from the internal one-way clutch.
Step 3: Inspect the Sensor Cable and Connector
- Locate the sensor harness exiting the bottom bracket shell or entering the side of the motor casing.
- Unplug the connector and check for bent pins, green corrosion, or moisture.
- Clean the pins with electrical contact cleaner, allow them to air-dry completely, and firmly seat the plug back together.
Step 4: Check for Axle Play
- Grab both crankarms firmly near the pedal ends.
- Rock the crankarms side-to-side across the frame to feel for movement.
- If there is noticeable lateral play or a distinct clunking sensation inside the bottom bracket, the load sensor cartridge has worn bearings and must be serviced. Learn more at E-Bike Torque Sensor Failure: Sluggish or No Assistance.
Stop Riding & Escalation Signs
Stop using electric assist if:
- The motor continues to push power after you stop pedaling.
- You feel metal-on-metal grinding inside the bottom bracket.
- Error 26 returns immediately after every system restart.
If cleaning the mechanical components and reseating connectors does not resolve Error 26, the internal load sensor cartridge or its dual-Hall sensor board has failed. On motors like the Bafang M600 or M620, resolving this requires removing the non-drive crankarm and utilizing a Bafang lockring tool to install a replacement torque/load sensor assembly.