Shimano Error E023: Motor Temperature Warning Fix

Shimano STEPS Error E023 indicates that the drive unit’s internal temperature sensor has detected excessive heat inside the motor housing. When operating temperatures exceed safe limits, the motor controller cuts electric assist immediately to protect the stator windings, internal planetary gears, and delicate control electronics from permanent thermal destruction. The code is self-clearing once the drive unit cools down to a safe operating temperature.

Fast Fix

Stop riding or shift into an easy mechanical gear and pedal manually without electrical assist. Park the bicycle in a shaded, well-ventilated area for 15 to 20 minutes to allow the motor housing to cool down naturally. Do not pour cold water over the hot motor casing. The error will clear automatically upon cooling.


Quick Status & Safety

  • Severity: Moderate. Motor assistance is shut off, but the display and manual pedaling function normally.
  • Safe to ride: Yes, purely under leg power. Mechanical pedaling will not damage the cooling drive unit.
  • Immediate safety concern: Never submerge the motor or spray cold water onto hot aluminum casings; thermal shock can crack internal seals and draw moisture into the motor.
  • Likely cause: Sustained steep climbing in Boost mode at low pedaling cadence, high ambient temperatures, thick mud insulating the motor cooling fins, or a heavy payload.

What This Means

Shimano STEPS drive units (such as the EP8, EP801, E8000, and E6100) are engineered with internal thermistors located directly on the motor controller circuit board and adjacent to the copper stator windings.

Under normal conditions, heat generated by electrical current flowing through the motor is conducted out through the aluminum drive unit shell. However, when you tackle sustained steep grades at a slow pedaling cadence, the electric motor operates in an inefficient RPM range. This causes current draw to spike dramatically, generating extreme heat. When internal sensors detect that temperatures have crossed the safe operating threshold, the firmware triggers Error E023 and shuts down motor power to prevent winding insulation from melting.


Diagnostic Path

Follow this checklist to determine why the drive unit overheated:

  1. The error triggered during a long, steep climb in Boost mode:
    • Suspect: Thermal overload from high current draw and low pedaling cadence (under 60 RPM).
  2. The error occurred on a hot summer day with high ambient air temperatures:
    • Suspect: Environmental heat saturation combined with standard motor operation.
  3. The error appeared during muddy or wet trail riding:
    • Suspect: Thick mud or debris caked over the motor skid plate and cooling fins, trapping heat inside the shell.
  4. The error appears immediately when powering on a completely cold bike:

Likely Causes

1. Low Cadence Under Heavy Assist (Motor Lugging)

Mid-drive motors are most efficient when spinning at high cadences (between 75 and 95 RPM). When riders grind up steep hills in Boost mode at low cadences (40–60 RPM) in a high mechanical gear, the motor is forced to deliver maximum torque without sufficient rotational speed. This generates rapid internal heat buildup.

2. Caked Mud or Debris Insulating the Motor Shell

The aluminum casing of the Shimano drive unit functions as its primary heat sink. If the bottom bracket area and skid plate are caked with thick mud, clay, or wet leaves, air cannot reach the aluminum fins, preventing heat dissipation.

3. High Ambient Temperatures and Direct Sunlight

Riding up steep grades in temperatures exceeding 90°F (32°C) reduces the thermal gradient between the motor shell and the surrounding air. The drive unit reaches its thermal limit much faster under these conditions.

4. Mechanical Drivetrain Drag

A dragging disc brake caliper, a severely worn chain, a seized bottom bracket bearing, or under-inflated tires force the motor to work substantially harder to maintain speed, elevating operating temperatures even on flat terrain.

5. Faulty Internal Thermistor

If the drive unit has suffered water intrusion or severe mechanical shock, the temperature sensor on the internal circuit board may fail open, reading maximum heat even when the aluminum casing is completely cold to the touch.


Commonly Confused Problems

  • Shimano Warning W011: On older Shimano displays, a temperature warning often begins as a “W” warning code (indicating thermal throttling where power is gradually reduced) before escalating to the hard cutoff of Error E023.
  • Shimano Error E010: E010 represents a generalized internal system error that can be caused by power delivery faults rather than simple thermal limits.
  • Shimano Error E020: A communication drop that occurs when an overheating controller logic board shuts down serial transmission. See Shimano Error E020: Communication Fault Fix.

What To Do

Step 1: Let the Motor Cool Down Naturally

  1. Pull off the trail or road and park the bicycle in the shade.
  2. Turn off the system to prevent any parasitic electrical draw from adding heat.
  3. Allow the bike to rest for 15 to 20 minutes.
  4. Check the aluminum casing with the back of your hand. Once it feels warm rather than burning hot, turn the system back on. The error should be gone, and full assist should be restored.

Step 2: Clear Dirt from the Motor Housing

  1. Inspect the underside of the motor and around the skid plate vents.
  2. Use a soft brush or a dry cloth to clear away caked mud, dried clay, and packed debris.
  3. Ensure the cooling airflow paths across the aluminum drive unit casing are completely clear.

Step 3: Adjust Gearing and Riding Cadence

  1. When resuming your ride on steep climbs, shift into a lower (easier) mechanical gear on your rear cassette.
  2. Increase your pedaling cadence to keep your legs spinning smoothly at 75 to 90 RPM.
  3. Drop your assist mode from Boost down to Trail or Eco. In Shimano’s Trail mode, the motor delivers progressive power based dynamically on your torque input, significantly reducing unnecessary heat buildup.

Step 4: Check for Mechanical Drag

  1. Lift the front and rear wheels off the ground and spin them by hand.
  2. Verify that disc brake pads are not rubbing against the brake rotors.
  3. Check tire pressures to ensure you are not rolling with excessive rolling resistance.

Stop Riding & Escalation Signs

Discontinue use and seek professional inspection if:

  • Error E023 appears instantly on a cold bike that has been sitting overnight in a cool room.
  • You notice a sweet chemical odor or the smell of burning electrical insulation coming from the drive unit.
  • The drive unit emits loud grinding, whining, or rattling mechanical noises when assist is active.

If Error E023 triggers when the motor is physically cold, the internal temperature sensor circuit on the drive unit board has failed. Because Shimano drive units are sealed factory assemblies that cannot be serviced internally by consumer mechanics, a failed temperature sensor requires replacement of the drive unit through an authorized Shimano service center.