Shimano STEPS Error E021 indicates that the drive unit has detected an unsupported, unauthorized, or firmware-incompatible battery. When this code appears, the system shuts down all electric pedal assistance as a safety precaution. In most cases, E021 occurs after a partial firmware update via the Shimano E-TUBE PROJECT app, when an uncertified third-party battery is connected, or when a genuine battery has an outdated internal Battery Management System (BMS) profile.
Fast Fix
Turn off the e-bike, remove the battery, and confirm it is a genuine Shimano STEPS pack (or a certified third-party unit like Darfon or Simplo). Reinstall the pack firmly until it clicks, launch the Shimano E-TUBE PROJECT app on your smartphone or PC, and perform a complete system update so all components share matching firmware versions.
Quick Status & Safety
- Severity: Moderate. Motor assistance is disabled, but lights, electronic shifting (Di2), and the display usually remain active.
- Safe to ride: Yes, strictly as a conventional bicycle without motor support.
- Likely cause: Firmware version mismatch between the battery and the drive unit, an unapproved aftermarket battery, or a corrupted initialization handshake.
What This Means
Shimano STEPS systems (including EP8, EP801, EP6, E8000, and E7000) use an encrypted digital handshake over the E-TUBE communication bus. When you power on the bike, the drive unit polls the battery’s internal BMS to verify its capacity, health parameters, and manufacturer security keys.
If the battery’s software protocol does not match what the drive unit firmware expects—or if the battery is an uncertified aftermarket pack lacking Shimano’s proprietary authentication credentials—the drive unit triggers Error E021. It blocks power flow to protect the motor’s power transistors and prevent unpredictable electrical behavior.
Diagnostic Path
Follow these practical checks to isolate the cause:
- The error appeared immediately after updating the bike’s firmware:
- Suspect: A firmware version mismatch. The drive unit or display updated, but the battery firmware failed to update or was skipped. Review Shimano Error E033: Firmware Mismatch Troubleshooting.
- The error occurred after swapping in a new or replacement battery:
- Suspect: An incompatible battery model or an uncertified third-party pack. Check the model number (e.g., BT-E8010, BT-E8035, BT-E8036) against Shimano’s official compatibility chart for your drive unit.
- The error appears intermittently on an existing, original battery:
- Suspect: Dirty communication contacts on the battery mount or a failing battery BMS logic board.
- The battery will not turn on or power the display at all:
- Suspect: The battery is in deep sleep or has a hardware lock. See Shimano Steps Battery Won’t Turn On? Try These Fixes.
Likely Causes
1. Incomplete or Mismatched E-TUBE Firmware
When updating a Shimano STEPS bike via Bluetooth using a smartphone, communication can drop mid-transfer. If the drive unit updates to a newer software standard while the battery remains on older code, the drive unit will reject the battery at the next boot, logging Error E021.
2. Unauthorized Third-Party Battery
Shimano allows select partner manufacturers (such as Darfon, Simplo, BMZ, and SMP) to produce integrated batteries for bike brands like Santa Cruz, Norco, and Canyon. However, generic, unapproved aftermarket batteries bought online lack the official encrypted handshake microchip, resulting in an immediate E021 lockout.
3. Corrupted BMS Initialization Handshake
If the power button on the battery or top-tube satellite switch is held too briefly or pressed repeatedly, the initialization sequence can hang. The drive unit boots before the battery finishes its internal self-check, generating an incompatibility flag.
4. Surface Oxidation on the Data Pins
The battery terminal block contains small auxiliary pins that transmit E-TUBE data. If dust, chain lube mist, or corrosion coats these contacts, data packets are corrupted, preventing the drive unit from reading the battery’s identification codes.
Commonly Confused Problems
- Shimano Error E025: Error E025 indicates an authentication failure, meaning the system detected an outright security key violation. See Shimano Error E025: Authentification Failure Fix.
- Shimano Error E022: Error E022 flags an internal communication loss during operation rather than an incompatibility check at startup. Consult Shimano Error E022: Internal Comm Failure Fix.
- Shimano Error E020: A generalized communication loss across the cockpit or entire E-TUBE network. Check Shimano Error E020: Communication Fault Fix.
What To Do
Step 1: Perform a Clean Cold Restart
- Turn off the system using the display or frame satellite power button.
- Remove the battery pack from the frame mount.
- Leave the battery unseated for two minutes.
- Remount the battery, ensuring it slides into the guide rails smoothly and latches firmly into the lock mechanism.
- Press the power button firmly once and allow the system 5 seconds to complete its boot sequence without touching the pedals or shifters.
Step 2: Connect to the Shimano E-TUBE PROJECT App
- Download or open the official Shimano E-TUBE PROJECT Cyclist app on your mobile device.
- Power on the e-bike and pair it via Bluetooth.
- Navigate to the Update tab.
- Check if the battery or drive unit displays an available update or a “Version Mismatch” warning.
- Apply all pending updates together. Ensure your phone remains near the bike and the screen stays on throughout the transfer. For advanced troubleshooting with PC tools, see Using Diagnostic Software for Bosch, Shimano, and Yamaha Systems.
Step 3: Inspect and Clean Battery Terminals
- Unseat the battery and inspect the multi-blade terminal connector on the frame mount (BM-E8010 or internal BM-E8035).
- Inspect the female slots on the battery pack for road dirt, dried mud, or corrosion.
- Spray electronic contact cleaner into the terminal openings and on the mount blades. Allow them to air-dry completely before remounting. For proper cleaner application, refer to How to Clean E-Bike Electrical Connectors Safely.
Stop Riding & Escalation Signs
Stop troubleshooting and seek assistance from an authorized Shimano service center if:
- The battery casing shows swelling, cracks, or heat discoloration around the terminal block.
- The E-TUBE app reports that the battery serial number is invalid or cannot be read.
- Error E021 persists across multiple reboot attempts on an original, factory-supplied battery.
If the battery firmware is verified up to date and all contacts are clean, an internal logic failure within the battery BMS is the likely culprit. A certified bike shop can connect the bike to the professional Shimano SM-PCE02 diagnostic box to run a hardware verification test and restore proper communication.