Bafang Error 25: Torque Sensor Signal Error Fix

Bafang Error 25 indicates that the motor controller has detected an invalid, out-of-range, or absent voltage signal from the torque sensor during operation. Torque sensors measure pedaling effort in millivolts; when this signal shorts to ground, spikes to the supply limit, or fluctuates erratically, the controller logs Error 25. To prevent unexpected motor acceleration or surges, the system automatically disables all pedal assistance.

Fast Fix

Turn off the e-bike display. Step completely off the pedals so that zero weight rests on the cranks. Inspect the torque sensor wiring connector near the bottom bracket or motor housing, disconnect and firmly reseat it, then turn the display back on without touching the pedals.


Quick Status & Safety

  • Severity: High. Pedal assistance will not function while the error is active.
  • Safe to ride: Yes, as a manual bicycle. If your e-bike is equipped with a throttle, it may still provide motor drive depending on your controller’s safety firmware.
  • Immediate safety concern: If the motor ever surges forward unprompted when the error clears, turn off the battery immediately.
  • Likely cause: Loose or wet torque sensor connector, internal strain gauge misalignment, excessive bottom bracket spindle play, or a failed sensor PCB.

What This Means

A torque sensor measures the physical twisting force you apply to the crankarms. Unlike a cadence sensor that simply tracks revolutions, the torque sensor uses internal strain gauges or magneto-elastic sensing elements to vary an output voltage:

  • Resting baseline: When you are not pushing on the pedals, the sensor outputs a stable resting voltage (typically 0.7V to 1.5V depending on whether it is an M500, M600, M620 Ultra, or external torque bottom bracket).
  • Under load: As you push down on the pedals, the voltage rises proportionally up toward 3.5V–4.2V.

If the controller detects a signal voltage below 0.4V (an open circuit or broken wire) or above 4.6V (a short circuit to the 5V power line), or if the reading jumps erratically between extremes while riding, it logs Error 25 and shuts off motor assist to protect the rider.


Diagnostic Path

Use these scenarios to determine why the torque signal is failing:

  1. The error appears only when you push hard on the pedals (e.g., climbing a hill or accelerating):
    • Suspect: Spindle flex causing an internal short, a loose crankarm rocking on the spindle, or an internal strain gauge that has debonded.
  2. The error appears immediately at power-on and will not clear:
    • Suspect: An unplugged sensor, a pinched or severed sensor wire, bent connector pins, or a fried sensor logic board.
  3. The throttle works perfectly, but pedal assist produces Error 25:
  4. The error started after riding through mud or power-washing the bottom bracket area:
    • Suspect: Water has breached the bottom bracket seals or the intermediate wiring harness connector.

Likely Causes

1. Loose or Corroded Sensor Plug

On Bafang mid-drive units, the torque sensor connects to the internal controller via a small multi-pin connector inside the non-drive-side casing or along an external lead. If road vibrations back this plug out, the signal circuit opens.

2. Spindle Play and Bottom Bracket Bearing Wear

If the bottom bracket bearings are worn or the lockring has loosened, the axle shifts off-center under rider weight. This mechanical misalignment distorts the magnetic gap between the rotating shaft and the stationary sensing coil, sending erratic voltages that trigger Error 25.

3. Internal Sensor Element Failure

Torque sensors endure constant mechanical stress. Over thousands of miles, the internal strain gauge elements, Hall-effect pickups, or internal ribbon cables can fracture. For deeper failure analysis, consult E-Bike Torque Sensor Failure: Sluggish or No Assistance.

4. Startup Calibration Offset

If you turn on the bike with your foot resting heavily on one pedal, the controller cannot set its zero-torque reference. While this condition usually triggers Error 17, certain CAN-bus firmware variants flag it as Error 25.


Commonly Confused Problems


What To Do

Step 1: Perform a No-Load Power Reboot

  1. Step off the bike and make sure both pedals are hanging completely free.
  2. Turn off the display and wait 15 seconds for all residual capacitance to dissipate.
  3. Turn the display back on without touching the cranks, pedals, or handlebars.
  4. Try pedaling gently down a flat street. If the error is gone, the issue was an uncalibrated zero-point reading at startup.

Step 2: Check for Crank and Spindle Play

  1. Grab the drive-side crankarm with one hand and the non-drive-side crankarm with the other.
  2. Push and pull firmly across the frame to feel for lateral play, clunking, or looseness in the bottom bracket axle.
  3. Tighten both crank bolts to factory torque specifications.
  4. If the axle itself shifts inside the motor housing, the bottom bracket bearings or bearing retaining ring must be tightened or serviced. For mid-drive mechanical teardowns, refer to Mid-Drive E-Bike Motor Problems: Common Internal Issues.

Step 3: Inspect the Torque Sensor Connector

  1. Locate the torque sensor lead exiting the bottom bracket (or open the non-drive-side motor cover on integrated units like the M600/M510/M620).
  2. Unplug the small round or flat sensor connector.
  3. Inspect the tiny gold pins for bends, corrosion, or water droplets.
  4. Clean with electrical contact cleaner, allow to dry, and reseat the connector firmly until it snaps into place.

Step 4: Test Signal Voltage with a Multimeter (Advanced)

If you have access to the sensor wires while connected:

  1. Set a digital multimeter to DC volts.
  2. Probe the signal return wire (usually white or green) against the ground wire (black).
  3. At rest, the reading should sit steadily between 0.7V and 1.5V.
  4. Stand on one pedal with the brakes locked to put heavy pressure on the crank. The voltage should rise smoothly to between 3.0V and 4.2V.
  5. If the reading stays locked at 0.0V (broken wire/dead board) or 5.0V (short to supply), the torque sensor assembly is defective and must be replaced.

Stop Riding & Escalation Signs

Stop riding under motor power and disconnect the battery if:

  • The motor continues to spin or run when you stop pedaling.
  • You feel a crunching or grinding sensation through the pedals, indicating collapsed bottom bracket bearings.
  • The error persists across multiple reboots and connector inspections.

Replacing a Bafang torque sensor assembly typically requires removing the crankarms and using a specialized bottom bracket lockring tool. If the sensor is tested and verified to output correct voltages but the display still logs Error 25, the analog-to-digital converter on the motor controller board has failed, requiring a replacement controller.