Bafang Error 27 indicates an over-current protection fault. The motor controller’s internal current-sensing circuit has detected an electrical draw that exceeds the hard-coded safety threshold of the controller’s power transistors (MOSFETs) or motor windings. When this threshold is breached, the controller cuts all power immediately to prevent the electronics from overheating, melting phase wire insulation, or suffering catastrophic board failure.
Fast Fix
Turn off the e-bike immediately and step off the bike. Allow the motor and controller to cool down for 15 minutes. Disconnect and inspect the battery terminals, shift your drivetrain into a lower mechanical gear, power the bike on, and ride off under gentle pedal assist without using the throttle from a complete stop.
Quick Status & Safety
- Severity: Critical. Motor power is cut to protect electrical components from thermal and electrical destruction.
- Safe to ride: Yes, as a manual bicycle, provided the rear wheel spins freely without resistance or shuddering.
- Immediate safety concern: If the motor hub or mid-drive casing feels blistering hot, or if you smell acrid burning plastic, disconnect the battery immediately and do not ride.
- Likely cause: Motor lugging under extreme load in too high a gear, melted phase wire connectors, shorted controller MOSFETs, or aggressive aftermarket controller settings.
What This Means
The motor controller is the bridge between the high-capacity battery pack and the motor’s three-phase copper windings. It uses a bank of power switching transistors (MOSFETs) to rapidly pulse current into the motor. A precision shunt resistor measures the exact amperage flowing through the board in real time.
Every Bafang controller has a factory current ceiling (for example, 15A on smaller hub motors, 25A on BBS02/HD, or 30A on M620 Ultra units). Under normal conditions, the controller limits power to stay under this ceiling. However, if the motor stalls under load, if phase wires touch each other, or if a MOSFET breaks down, current spikes dramatically. The controller detects this spike and logs Error 27 within milliseconds.
Diagnostic Path
Use these scenarios to identify the source of the over-current event:
- The error triggered while climbing a steep hill or hauling cargo:
- Suspect: Thermal/electrical overload from lugging the motor at low RPM in a high mechanical gear. Review E-Bike Motor Cutting Out Under Load or on Hills.
- The error appears instantly at power-on, and the motor resists spinning by hand:
- Suspect: Blown controller MOSFETs that have fused into a permanent short circuit across the phase lines.
- The error appeared after an aggressive throttle start from a dead stop:
- Suspect: Initial startup current spike, particularly if high assist levels or modified programming are in use.
- The error appeared after modifying controller firmware or changing shunt resistance:
- Suspect: Firmware parameters exceeding hardware capacity. See E-Bike Controller Shunt Mod Risks: Blown Boards and Failures.
Likely Causes
1. Motor Lugging (High Load, Low Cadence)
Electric motors are least efficient and draw maximum current when spinning slowly under heavy load. If you tackle a steep incline in a high gear using throttle only, the motor stalls or turns at very low RPM. This turns electrical energy directly into extreme heat and current draw, triggering over-current cutoffs. Check Why Your E-Bike Controller is Cutting Power Under Load.
2. Shorted Controller MOSFETs
The power transistors inside the controller can fail under heat stress. When a MOSFET fails, it almost always fails short, connecting a motor phase directly to positive or ground. This causes an instantaneous over-current fault the moment the bike powers up. See Identifying MOSFET Failure in Brushless E-Bike Controllers.
3. Melted or Shorted Phase Wires
The three heavy-gauge phase wires (typically blue, green, and yellow) deliver motor power. Under sustained loads, bullet or Anderson connectors can overheat, melt their plastic housings, and touch, creating a direct phase-to-phase dead short. See How to Fix Melted Phase Wire Connectors (Anderson vs. Bullet).
4. Current Sensor / Shunt Calibration Failure
The controller reads amperage across a metal shunt resistor. If the solder joints around this shunt crack, or if the internal amplifier fails, the controller misreads normal current as a dangerous over-current event. For related sensor faults, see Bafang Error 12: Controller Current Sensor Fault.
Commonly Confused Problems
- Bafang Error 10/11/15: These errors flag controller or motor overheating before an electrical limit is breached. Error 27 is an immediate current limit shutdown rather than a gradual thermal ramp-down.
- Bafang Error 08: Indicates a motor Hall sensor fault, which can cause rough motor stuttering that mimics over-current cutouts.
What To Do
Step 1: Allow the Drive Unit to Cool Down
- Turn off the bike and pull off the road.
- Let the motor and controller sit in the shade for at least 15 to 20 minutes.
- Feel the motor housing with the back of your hand. If it is hot to the touch, wait until it returns to ambient temperature before attempting to restart.
Step 2: Check for Phase Short Resistance
- Elevate the drive wheel (rear wheel for hub motors, or spin the cranks for mid-drives) with the bike turned off.
- Spin the wheel by hand.
- If the wheel spins freely with normal bearing resistance, the phase wires and MOSFETs are likely intact.
- If the wheel feels stiff, notched, or resists turning as if the brakes are on, the phase wires are shorted together or the controller’s MOSFETs are blown.
Step 3: Inspect Phase Wiring and Connectors
- Access the wiring harness entering the hub motor or open the controller compartment.
- Locate the thick yellow, blue, and green motor phase wires.
- Slide back any rubber insulation boots or inspect the plastic connector housings.
- Look for melted plastic, blackened metal terminals, or heat-shrunk wire that has burned through.
- If terminals have melted, cut them back, strip clean copper, and solder new high-amperage connectors.
Step 4: Adjust Riding Style and Settings
- When restarting the bike, shift into a low mechanical gear so your pedaling cadence stays high (70–90 RPM).
- Never rely solely on full throttle from a dead stop when facing an uphill incline; always pedal to help the motor get up to speed.
- If you use a custom programming cable, restore the factory Bafang current limits (e.g., lower “Current Limit” from 30A back to factory specs).
Stop Riding & Escalation Signs
Do not attempt to ride under power and disconnect the battery immediately if:
- The motor resists manual rotation or shudders violently upon power application.
- You see smoke, melted wire sheaths, or smell burning insulation.
- Error 27 returns immediately at zero speed under no load.
If Error 27 appears on a cold bike and the motor resists turning by hand, one or more MOSFETs on the controller board have blown. The controller must be replaced.