Bafang Error 24: Light Sensor Fault Fix

Bafang Error 24 indicates that the display’s ambient light sensor has malfunctioned, become disconnected, or is returning an out-of-range voltage reading. Modern Bafang displays equipped with automatic backlighting and auto-headlight controls use a small photocell to monitor ambient daylight. When the signal from this sensor drops to absolute zero, shorts out, or freezes beyond expected thresholds, the system logs Error 24.

Fast Fix

Inspect the top edge and face of your handlebar display for mud, tape, stickers, or heavy dirt obscuring the clear ambient light sensor window. Clean the display with a microfiber cloth, enter the display settings menu, disable the automatic headlight (“Auto Light”) feature by setting it to manual, and restart the bike.


Quick Status & Safety

  • Severity: Low. The bike remains fully rideable with functional pedal assistance and throttle.
  • Safe to ride: Yes. Error 24 is a non-critical accessory fault that does not impact motor torque, speed governor control, or battery health.
  • Likely cause: Blocked or dirty light sensor window, internal moisture inside the display casing, cracked display glass, or a failing display photocell.

What This Means

Displays such as the Bafang DPC-18, C240, C241, and various color CAN-bus units incorporate an ambient light sensor (a small photodiode or photoresistor). This sensor measures environmental daylight and performs two tasks:

  1. It automatically dims the LCD screen in dark conditions and brightens it under direct sunlight to prevent rider glare.
  2. It automatically turns on the front and rear lights at dusk or when entering tunnels, provided the system is configured in “Auto” mode.

The display’s microcontroller expects the light sensor to return an analog voltage between designated boundaries (typically between 0.3V and 4.7V). If internal moisture shorts the sensor pin to 0V (ground) or 5V (reference rail), or if the photodiode circuit fails completely, the display logs Error 24.


Diagnostic Path

Follow this checklist to determine the root cause:

  1. The error appeared immediately after washing the bike or leaving it out in heavy rain:
  2. The error appears only when turning on the bike in a pitch-black garage or unlit room:
    • Suspect: Some display firmware profiles register complete zero-lux conditions as an open-circuit fault if the photodiode calibration threshold is corrupted.
  3. The display is scratched, cracked, or has heavy sun-fade/crazing on the lens:
  4. The error occurred after adjusting settings in the display menu:
    • Suspect: The auto-light sensitivity parameter was set outside functional parameters, or an incompatible display was paired with the system.

Likely Causes

1. Obscured Sensor Aperture

The sensor window is tiny—often no larger than a pinhead—located along the top edge or upper bezel of the display. A smear of grease, mud, electrical tape, or an overlapping phone mount can block light completely, confusing the sensor logic.

2. Moisture Trapped Inside the LCD Housing

Budget and mid-tier displays rely on rubber perimeter seals that degrade over time. Condensation forming on the inside of the glass directly bridges the exposed pins of the ambient light photodiode.

3. Display Menu Configuration Glitch

If the automatic lighting threshold is corrupted, the display’s firmware may flag the sensor as unresponsive during system self-checks. Disabling the auto feature bypasses the sensor circuit check on many firmware builds.

4. Photodiode Component Failure

Vibration from rough roads and trail riding can crack the micro-soldered solder joints connecting the photodiode to the display’s main printed circuit board (PCB).


Commonly Confused Problems


What To Do

Step 1: Clean and Inspect the Sensor Port

  1. Turn off the e-bike.
  2. Use a damp microfiber cloth with mild soapy water to clean the entire outer face, top edge, and corners of the display unit.
  3. Ensure no stickers, zip ties, or handlebar accessory clamps are casting a shadow over or touching the sensor window.
  4. Dry thoroughly with a clean towel.

Step 2: Disable the Auto-Light Feature in the Display Menu

  1. Power on the display.
  2. Double-click or long-press the “Menu” or “Info” button to enter the main settings interface.
  3. Navigate to the “Auto Light” or “Light Sens” (Light Sensitivity) menu.
  4. Adjust the setting from “Auto” to “OFF” or change the sensitivity to “0”.
  5. Save the setting and exit the menu.
  6. Power cycle the bike. On most Bafang firmware versions, disabling the automatic feature stops the system from polling the sensor, clearing Error 24 permanently while allowing manual light control.

Step 3: Check for Internal Condensation

  1. Look closely at the display screen under bright light.
  2. If you see fogging, water droplets, or cloudiness under the lens, the light sensor circuit is wet.
  3. Remove the display from the handlebars, bring it into a dry, warm indoor room, and allow it to dry out for 24 to 48 hours. A bag with silica gel packets can accelerate this process.
  4. Avoid using high heat or hair dryers, which will melt the polarizing film inside the LCD.

Step 4: Disconnect and Reseat the Display Harness

  1. Locate the round green 5-pin display connector roughly 4 to 8 inches down the handlebar harness.
  2. Unplug the connector by pulling straight apart.
  3. Check for bent pins or moisture, spray with electrical contact cleaner, and firmly reconnect the plug, matching the alignment arrows. For general display cable troubleshooting, review Fixing an E-Bike Display Not Communicating with the Controller.

Stop Riding & Escalation Signs

Because Error 24 does not compromise braking, battery safety, or motor operation, you can safely continue riding.

However, if you cannot clear the error by disabling the auto-light menu setting, or if the screen shows visible internal water damage, the photodiode has failed permanently. Because the light sensor is surface-mounted inside the sealed display unit, individual component repair is rarely practical. Replacing the display unit with a compatible UART or CAN-bus model is the definitive fix.